RUN 'N STITCH
  • Home
  • Blog
  • Tutorials
  • Free Patterns
  • About

Binding Tutorial

10/31/2024

0 Comments

 
Binding the raw edges of your finished piece is the final stage, where the active process of machine sewing the binding to the quilt followed by the passive and reflective process of hand sewing bring closure to your work.

Picture
First you must choose the fabric you will use for your binding.   It is likely you will need more than one strip so cut enough 2-1/2" strips, that when sewn together, will make a strip long enough to go completely around your quilt.

Picture
​​You will need to sew these strips together.  It is best to sew them on the diagonal so they don't cause lumps in the side of your piece.  

Picture
  ​ Chain Piece your strips.

Picture
Picture
Cut the excess 1/4 inch away from the seam stitching..

Picture
Press the seam to one side.

Picture
​Fold the binding strip in half, wrong sides together, and press.  You will have a long 1-1/4" strip.

Picture
​Trim your quilt sandwich so the edges are straight.

Picture
​Match the raw edges of the folded 1-1/4" strip to the raw edge of the quilt top. 
​
Leave about 12" of the strip loose. 

Picture
 Using a 1/4" seam sew the binding strip to the quilt top. I use my walking foot for this step.

Picture
​Stop when you get 1/4" from the end of the quilt top, at the corner.
​ 
Backstitch to secure the seam.  Cut the thread.

Picture
​Turn your quilt around as shown in the picture below.  
​
Fold the binding so you have a 45 degree angle as shown below.

Picture
Fold the binding down and match the raw edges again as shown below. ​

Picture
​Using a back stitch to secure the seam, begin at the top of the quilt/binding and sew to 1/4" before the next corner.

​Follow the same procedure to turn each corner.

Picture
Leave a 12 inch unsewn opening between the beginning and end of your binding
 
 
You should have 12 inches of unsewn binding strip at each end.



Picture
Open your binding and using a small ruler and mat, make a 45 degree diagonal cut on one side of the binding strip.

Picture
Lay your small cutting board on top of the quilt where you are cutting your binding strips.  Put the the uncut binding strip on top of the board and then lay the cut strip on top of the uncut strip.  using your small ruler, measure 1/2 inch from the top edge of the diagonal strip and mark the uncut strip.

Picture
Move the cut strip out of the way.  Using the marking as a reference point, lay your small square on the uncut strip.  Be sure your cutting the diagonal the right way.  I've made this mistake.

Picture
After your two sides are cut,  sew your binding pieces together.  Having a large opening helps with this step.  Twelve inches is a bare minimum.  

Picture
Sew the binding onto the quilt.

Picture
 Press the binding away from your quilt top.

Picture
 Turn your work over and press the binding so it covers the seam on the back side.

Picture
 Press your binding all the way to the end of the corner so you can make a crisp corner.

Picture
 Fold he binding at the corner so you have a 45 degree angle at the back of the piece.

Picture
Hand sew the binding at the back using a blind stitch.

Picture
Sit back and admire and enjoy your lovely finished project.

0 Comments

Pillowcase Pattern

10/29/2024

0 Comments

 
This is the best pillow case pattern ever.  You can choose your fabric and then whip this baby together in a few minutes.   ​
Picture
Standard Pillow Case
For each pillow case you will need:

1/4 Yard Cuff Fabric
3/4 Yard Pillow Body Fabric
2” Strip (optional) Cut WOF.  Iron the trim, lengthwise, wrong sides together.  You should have a 1”X 42” strip.
Picture
​Place the cuff fabric on a hard surface, right side up.

​
Place the trim on top of the cuff, matching raw edges at the top end of the cuff.  Note, your salvage edges will be on each side of the cuff and the raw edges will be at the top and bottom.
Picture
Lay the pillow body fabric on top of the cuff and the trim, right side down, matching the raw edges.  PIN, PIN, PIN.... be sure to pin the three sections together securely.
Picture

Roll the pillow body up toward the pinned edge. Be sure to leave room for a seam. ​
Picture

Wrap the unpinned edge of the cuff fabric around the body fabric roll.  RE-PIN securely in place. ​
Picture
Sew a 1/4” seam across the pinned edge, removing pins as you go.  Press the seam to set it.  Pull the pillow case body roll out of the sleeve case.  ​
Picture
Picture
Press your seams flat.
Picture
Fold your pillowcase in half matching selvedge edges, wrong sides together.  Pin the trim of the pillowcase  so it stays together when you cut.   Line your ruler up with the cuff of the pillowcase so your cut will be straight.  Then, trim the salvage edges off of your pillowcase..
Picture
Picture
Cut the bottom of the pillow case to square it up.
Picture
 After your case is trimmed nice and straight, with fabric wrong sides together, pin the raw edges and sew them together using a 1/8" seam.
Picture
Trim the corners.
Picture
Turn the pillowcase inside out and pin the top and trim pieces in place.  Sew a 1/4” seam on the inside of the pillowcase, along the seam edges. This seam will encase the raw edge on first seam.
Picture
Picture

Turn the pillowcase right side out and press the pillowcase one last time.
0 Comments

    Author

    Hello and Welcome!  My name is Kathi and I've lived in Alaska forever.  I love to sew and craft the long winter nights away. 

    Categories

    All

    Archives

    December 2024
    October 2024
    April 2023

    RSS Feed

  • Home
  • Blog
  • Tutorials
  • Free Patterns
  • About